NC(1)                     BSD General Commands Manual                    NC(1)

     nc -- arbitrary TCP and UDP connections and listens

     nc [-46bCDdFhklNnrStUuvZz] [-I length] [-i interval] [-M ttl] [-m minttl]
        [-O length] [-P proxy_username] [-p source_port] [-q seconds]
        [-s source] [-T keyword] [-V rtable] [-w timeout] [-X proxy_protocol]
        [-x proxy_address[:port]] [destination] [port]

     The nc (or netcat) utility is used for just about anything under the sun
     involving TCP, UDP, or UNIX-domain sockets.  It can open TCP connections,
     send UDP packets, listen on arbitrary TCP and UDP ports, do port scan-
     ning, and deal with both IPv4 and IPv6.  Unlike telnet(1), nc scripts
     nicely, and separates error messages onto standard error instead of send-
     ing them to standard output, as telnet(1) does with some.

     Common uses include:

           o   simple TCP proxies
           o   shell-script based HTTP clients and servers
           o   network daemon testing
           o   a SOCKS or HTTP ProxyCommand for ssh(1)
           o   and much, much more

     The options are as follows:

     -4      Forces nc to use IPv4 addresses only.

     -6      Forces nc to use IPv6 addresses only.

     -b      Allow broadcast.

     -C      Send CRLF as line-ending.

     -D      Enable debugging on the socket.

     -d      Do not attempt to read from stdin.

     -F      Pass the first connected socket using sendmsg(2) to stdout and
             exit.  This is useful in conjunction with -X to have nc perform
             connection setup with a proxy but then leave the rest of the con-
             nection to another program (e.g. ssh(1) using the ssh_config(5)
             ProxyUseFdpass option).

     -h      Prints out nc help.

     -I length
             Specifies the size of the TCP receive buffer.

     -i interval
             Specifies a delay time interval between lines of text sent and
             received.  Also causes a delay time between connections to multi-
             ple ports.

     -k      Forces nc to stay listening for another connection after its cur-
             rent connection is completed.  It is an error to use this option
             without the -l option.  When used together with the -u option,
             the server socket is not connected and it can receive UDP data-
             grams from multiple hosts.

     -l      Used to specify that nc should listen for an incoming connection
             rather than initiate a connection to a remote host.  It is an
             error to use this option in conjunction with the -p, -s, or -z
             options.  Additionally, any timeouts specified with the -w option
             are ignored.

     -M ttl  Set the TTL / hop limit of outgoing packets.

     -m minttl
             Ask the kernel to drop incoming packets whose TTL / hop limit is
             under minttl.

     -N      shutdown(2) the network socket after EOF on the input.  Some
             servers require this to finish their work.

     -n      Do not do any DNS or service lookups on any specified addresses,
             hostnames or ports.

     -O length
             Specifies the size of the TCP send buffer.

     -P proxy_username
             Specifies a username to present to a proxy server that requires
             authentication.  If no username is specified then authentication
             will not be attempted.  Proxy authentication is only supported
             for HTTP CONNECT proxies at present.

     -p source_port
             Specifies the source port nc should use, subject to privilege
             restrictions and availability.

     -q seconds
             after EOF on stdin, wait the specified number of seconds and then
             quit. If seconds is negative, wait forever (default).  Specifying
             a non-negative seconds implies -N.

     -r      Specifies that source and/or destination ports should be chosen
             randomly instead of sequentially within a range or in the order
             that the system assigns them.

     -S      Enables the RFC 2385 TCP MD5 signature option.

     -s source
             Specifies the IP of the interface which is used to send the pack-
             ets.  For UNIX-domain datagram sockets, specifies the local tem-
             porary socket file to create and use so that datagrams can be
             received.  It is an error to use this option in conjunction with
             the -l option.

     -T keyword
             Change IPv4 TOS value.  keyword may be one of critical,
             inetcontrol, lowcost, lowdelay, netcontrol, throughput,
             reliability, or one of the DiffServ Code Points: ef, af11 ...
             af43, cs0 ... cs7; or a number in either hex or decimal.

     -t      Causes nc to send RFC 854 DON'T and WON'T responses to RFC 854 DO
             and WILL requests.  This makes it possible to use nc to script
             telnet sessions.

     -U      Specifies to use UNIX-domain sockets.

     -u      Use UDP instead of the default option of TCP.  For UNIX-domain
             sockets, use a datagram socket instead of a stream socket.  If a
             UNIX-domain socket is used, a temporary receiving socket is cre-
             ated in /tmp unless the -s flag is given.

     -V rtable
             Set the routing table to be used.

     -v      Have nc give more verbose output.

     -w timeout
             Connections which cannot be established or are idle timeout after
             timeout seconds.  The -w flag has no effect on the -l option,
             i.e. nc will listen forever for a connection, with or without the
             -w flag.  The default is no timeout.

     -X proxy_protocol
             Requests that nc should use the specified protocol when talking
             to the proxy server.  Supported protocols are ``4'' (SOCKS v.4),
             ``5'' (SOCKS v.5) and ``connect'' (HTTPS proxy).  If the protocol
             is not specified, SOCKS version 5 is used.

     -x proxy_address[:port]
             Requests that nc should connect to destination using a proxy at
             proxy_address and port.  If port is not specified, the well-known
             port for the proxy protocol is used (1080 for SOCKS, 3128 for
             HTTPS).  An IPv6 address can be specified unambiguously by
             enclosing proxy_address in square brackets.

     -Z      DCCP mode.

     -z      Specifies that nc should just scan for listening daemons, without
             sending any data to them.  It is an error to use this option in
             conjunction with the -l option.

     destination can be a numerical IP address or a symbolic hostname (unless
     the -n option is given).  In general, a destination must be specified,
     unless the -l option is given (in which case the local host is used).
     For UNIX-domain sockets, a destination is required and is the socket path
     to connect to (or listen on if the -l option is given).

     port can be a specified as a numeric port number, or as a service name.
     Ports may be specified in a range of the form nn-mm.  In general, a des-
     tination port must be specified, unless the -U option is given.

     It is quite simple to build a very basic client/server model using nc.
     On one console, start nc listening on a specific port for a connection.
     For example:

           $ nc -l 1234

     nc is now listening on port 1234 for a connection.  On a second console
     (or a second machine), connect to the machine and port being listened on:

           $ nc 1234

     There should now be a connection between the ports.  Anything typed at
     the second console will be concatenated to the first, and vice-versa.
     After the connection has been set up, nc does not really care which side
     is being used as a 'server' and which side is being used as a 'client'.
     The connection may be terminated using an EOF ('^D').

     There is no -c or -e option in this netcat, but you still can execute a
     command after connection being established by redirecting file descrip-
     tors. Be cautious here because opening a port and let anyone connected
     execute arbitrary command on your site is DANGEROUS. If you really need
     to do this, here is an example:

     On 'server' side:

           $ rm -f /tmp/f; mkfifo /tmp/f
           $ cat /tmp/f | /bin/sh -i 2>&1 | nc -l 1234 > /tmp/f

     On 'client' side:

           $ nc 1234
           $ (shell prompt from

     By doing this, you create a fifo at /tmp/f and make nc listen at port
     1234 of address on 'server' side, when a 'client' establishes a
     connection successfully to that port, /bin/sh gets executed on 'server'
     side and the shell prompt is given to 'client' side.

     When connection is terminated, nc quits as well. Use -k if you want it
     keep listening, but if the command quits this option won't restart it or
     keep nc running. Also don't forget to remove the file descriptor once you
     don't need it anymore:

           $ rm -f /tmp/f

     The example in the previous section can be expanded to build a basic data
     transfer model.  Any information input into one end of the connection
     will be output to the other end, and input and output can be easily cap-
     tured in order to emulate file transfer.

     Start by using nc to listen on a specific port, with output captured into
     a file:

           $ nc -l 1234 > filename.out

     Using a second machine, connect to the listening nc process, feeding it
     the file which is to be transferred:

           $ nc -N 1234 <

     After the file has been transferred, the connection will close automati-

     It is sometimes useful to talk to servers ``by hand'' rather than through
     a user interface.  It can aid in troubleshooting, when it might be neces-
     sary to verify what data a server is sending in response to commands
     issued by the client.  For example, to retrieve the home page of a web

           $ printf "GET / HTTP/1.0\r\n\r\n" | nc 80

     Note that this also displays the headers sent by the web server.  They
     can be filtered, using a tool such as sed(1), if necessary.

     More complicated examples can be built up when the user knows the format
     of requests required by the server.  As another example, an email may be
     submitted to an SMTP server using:

           $ nc [-C] localhost 25 << EOF
           MAIL FROM:<>
           RCPT TO:<>
           Body of email.

     It may be useful to know which ports are open and running services on a
     target machine.  The -z flag can be used to tell nc to report open ports,
     rather than initiate a connection. Usually it's useful to turn on verbose
     output to stderr by use this option in conjunction with -v option.

     For example:

           $ nc -zv 20-30
           Connection to 22 port [tcp/ssh] succeeded!
           Connection to 25 port [tcp/smtp] succeeded!

     The port range was specified to limit the search to ports 20 - 30, and is
     scanned by increasing order.

     You can also specify a list of ports to scan, for example:

           $ nc -zv 80 20 22
           nc: connect to 80 (tcp) failed: Connection refused
           nc: connect to 20 (tcp) failed: Connection refused
           Connection to port [tcp/ssh] succeeded!

     The ports are scanned by the order you given.

     Alternatively, it might be useful to know which server software is run-
     ning, and which versions.  This information is often contained within the
     greeting banners.  In order to retrieve these, it is necessary to first
     make a connection, and then break the connection when the banner has been
     retrieved.  This can be accomplished by specifying a small timeout with
     the -w flag, or perhaps by issuing a "QUIT" command to the server:

           $ echo "QUIT" | nc 20-30
           Protocol mismatch.
           220 IMS SMTP Receiver Version 0.84 Ready

     Open a TCP connection to port 42 of, using port 31337 as
     the source port, with a timeout of 5 seconds:

           $ nc -p 31337 -w 5 42

     Open a UDP connection to port 53 of

           $ nc -u 53

     Open a TCP connection to port 42 of using as
     the IP for the local end of the connection:

           $ nc -s 42

     Create and listen on a UNIX-domain stream socket:

           $ nc -lU /var/tmp/dsocket

     Connect to port 42 of via an HTTP proxy at,
     port 8080.  This example could also be used by ssh(1); see the
     ProxyCommand directive in ssh_config(5) for more information.

           $ nc -x10.2.3.4:8080 -Xconnect 42

     The same example again, this time enabling proxy authentication with
     username ``ruser'' if the proxy requires it:

           $ nc -x10.2.3.4:8080 -Xconnect -Pruser 42

     cat(1), ssh(1)

     Original implementation by *Hobbit* <>.
     Rewritten with IPv6 support by Eric Jackson <>.
     Modified for Debian port by Aron Xu <>.

     UDP port scans using the -uz combination of flags will always report suc-
     cess irrespective of the target machine's state.  However, in conjunction
     with a traffic sniffer either on the target machine or an intermediary
     device, the -uz combination could be useful for communications diagnos-
     tics.  Note that the amount of UDP traffic generated may be limited
     either due to hardware resources and/or configuration settings.

BSD                            February 9, 2017                            BSD

Man(1) output converted with man2html
list of all man pages